What is the perfect size Jon boat?
If you plan on using your Jon boat for things like camping expeditions, where you will likely have more people and gear on the boat, a 12 to 14-foot model is ideal. At this size, you can pack a little more weight and will be able to accommodate a larger motor to get you further.
Is a 12 foot Jon boat big enough?
As boat length increases the weight capacity similarly increase, so with a 12 foot boat approximately 400 lbs can be safely contained and at 14 foot 400+ lbs. … An 18 foot Jon boat will hold, on average, about 1,500 lbs. At 20+ feet in length a jon boat is able to hold up to 1,900 lbs of people and equipment.
What is the average size of a Jon boat?
Jon boats are available commercially between 8 and 24 feet (2.4 and 7.3 m) long and 32 to 60 inches (81 to 152 cm) wide, though custom sizes may be found. The simple design includes an open hull, without a bilge, leaving the ribs exposed.
How do I choose a Jon boat?
Look for an aluminum flat-bottomed jon boat that is stable and rugged. If you are still learning the boating basics, this boat will hold up to brushes with rocky shorelines or bumps into docks. When choosing a fishing boat of any type, having enough storage space for tackle and safety gear is important.
Do they make 8 ft jon boats?
8-foot Jon Boat (2.4 m)
Crew: 1-2 people. Preferably one adult and a child. The 8-foot model is likely the smallest jon boat you can buy from a manufacturer.
How much is a 12 foot aluminum boat worth?
The purchasing price of a Jon boat will depend on its make, size, construction material and the number of modifications made to the boat. A cheap 12 ft polythene Jon boat can be bought for as little as $550 while an 12 ft aluminum Jon boat can cost as much as $3000. High-end 21 ft Jon boats can cost as much as $30,000.
What size motor do I need for a 14 foot boat?
Typical horsepower for a 14-foot jon boat would be between 15 HP and 20 HP although up to 25 HP is not uncommon either. 20 HP can comfortably give you a top speed of 20mph, potentially even stretching to 25mph depending on weather conditions and the weight on the boat.
How big of a motor can you put on a 14ft boat?
12 foot – 10 – 15 hp motor. 14 foot -15 hp motor. 16 foot – 15 – 20 hp motor. 18 foot – 18 – 20 hp motor.
What size motor should I put on my boat?
The rule of thumb is based on weight alone, and says you should have between 40 and 25 pounds of weight for each horsepower. For example, a 5,000-pound boat could have an engine with between 125 and 200 horsepower.
Is a 14 ft boat too small?
It depends on what you’re wanting to do. If you fish solo, a 12′ or 14′ boat is fine. A Carolina Skiff has no vee, so they’ll be as stable as you can expect.
How fast will a 9.9 hp boat motor go?
Assuming this is a light 14′ utility boat and a standard 9.9, Mercury would recommend a 8.5 to 9.5 pitch prop for the OP’s application and predicts a top speed around 20 mph.
How fast will a 14 foot jon boat go?
14ft Alumacraft T-14s with 15 HP Honda. Tops out at about 25 mph with just me in the boat.
Why is it called a jon boat?
It is told that fishermen in Scandinavia loved using flat bottomed boats to carry themselves and their fishing gear to the larger boats. Because the boats were stable and easy to construct, they became favorite transportation for many fishermen. … And a few of the fishermen were named “Jon” or “John”.
How heavy is a 14 foot aluminum boat?
You can find some v-hull designs that are in the 150-pound range, which are reasonably easy to move around. But flat-bottomed jon boats tend to weigh more. Add in under-floor storage and a wider design and weights approaching 300 pounds are possible.
Can a jon boat go in the ocean?
Jon boats can go in the ocean but only under very specific conditions. A mod-v Jon boat is the best choice for ocean use but only in optimal calm weather conditions and never far from shore. The flat bottom and low freeboard make a Jon boat unsuitable for rough ocean water.
Is Jon boat flat bottom?
Jon boats have a flat or nearly flat bottom. They have squared-off bows rather than coming to a point at the front. Most jon boats are made of aluminum, though there are also a handful of fiberglass and roto-molded polyethylene models on the market.
Do jon boats sink?
Jon boats rarely flip but they can easily take on enough water to sink when they are not used correctly. Below are a few things you can do to ensure your Jon boat does not take on water. … Avoid overloading the boat. Ensure you distribute the load correctly.
Do jon boats have titles?
Registration requirements vary from State to State though a common theme is that motorized Jon boats require registration (and sometimes titling) whereas non-motorized Jon boats do not require registration or titling.
Can you leave an aluminum boat in the water?
Aluminum Can Do Well in Salt and Freshwater
However, to play it safe, the American Boat and Yacht Council (ABYC) recommends that “aluminum vessels shall have a protective paint coating that provides a high [electrical] resistance barrier between the aluminum and the water.”
Are Jon boats motorized?
Typically made of aluminum and powered by a small outboard motor, jon boats are lightweight and rugged, and can be found in service around the world for fishing and hunting, search-and-rescue, and as workboats.
What is the advantage of a Jon boat?
Advantages of Jon Boats
Jon boats are known to be flat bottomed boats, which offer users a very stable ride. This is one of the reasons that so many jon boats are used for fishing and for utility reasons around a marina. You can easily get in and out of them as well as move around while you are on the water.
Should I paint the bottom of my aluminum boat?
If you want to leave your aluminum boat in the water for extended periods of time, anti-fouling paint may be necessary to prevent growth on the bottom. And regular paint and clear coat isn’t intended to do this job – you need a paint specifically formulated to be anti-fouling.
Do aluminum boats rust?
Although aluminium boats are corrosion resistant, they are not corrosion proof, especially if a low-grade aluminium is used. Luckily, there are a variety of ways to prevent and protect your boat from the effects of oxidation and corrosion.
Is salt water bad for aluminum boats?
Yes, salt water corrosion does damage aluminum boats. Over time, aluminum slowly oxidates in saltwater. The electrochemical inside the aluminum of the boat isn’t strong enough to handle the harsh effects of corrosion caused by the saltwater. Aluminum does a great job of resisting corrosion most of the time.