What does it mean when an interface does not display configuration settings when using the show running-config?
What does it mean when an interface does NOT display configuration settings when using the show running-config and show startup-config commands? Question 38 options: A) It means the interface is not active.
What does the switch config )# prompt indicate?
Global configuration mode, indicated by the routername(config)# prompt, allows configuration changes to be made that apply to the entire router (as opposed to a configuration change that might affect only one interface, for example).
Which of the following commands displays a router’s configuration?
Router#show running-config
This command will display the configuration currently running in RAM.
What is the command to delete the configuration stored in Nvram on a device include the mode?
The command erase startup-config deletes the configuration stored in NVRAM.
What is configuration mode?
Global Configuration mode mode allows users to modify the running system configuration. From the Privileged mode a user can move to configuration mode by running the “configure terminal” command from privileged mode. To exit configuration mode, the user can enter “end” command or press Ctrl-Z key combination.
How do I go back to privileged mode?
To return to privileged EXEC mode, enter the end command, or press Ctrl-Z. After you access the device, you are automatically in user EXEC command mode. The EXEC commands available at the user level are a subset of those available at the privileged level.
What command erases the startup configuration?
Enter config-register 0x2102. Enter end, and then enter the write erase command to delete the current startup configuration on the router.
Why is it necessary to erase the startup configuration?
Why is it necessary to erase the startup configuration before reloading the router? The startup configuration file is loaded into memory and becomes the running-config after the router reloads. Erasing this file allows the router to return to its basic configuration after a reload.
How do I clear my running config?
To clear out the running config file, simply erase the startup config file and then reload the device.
How do I clear the configuration on an HP switch?
Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch. The power and fault lights come on. Continue to press the Clear button while releasing the Reset button. When the Self Test LED begins to blink, release the Clear button.
What does the command routerA config )# line cons 0 allow you to perform next 1 point?
Telnet password
What does the command routerA(config)#line cons 0 allow you to perform next? Set the Telnet password.
How do I get my router out of ROMmon mode?
If your router gets stuck in ROMmon mode during the boot process, examine the value of the configuration register by entering the confreg command. Change the value of the configuration register as shown below to stop the router to go into the ROMmon mode after reloading.
How do I factory reset my HP Deskjet 2650?
To execute the factory default reset on the switch, perform these steps:
- Simultaneously press the Reset and Clear buttons on the front of the switch with a paperclip.
- Continue to hold the Clear button while releasing the Reset button.
- When the Self Test LED begins to blink, release the Clear button.
How do I configure my HP switch?
To do so, do one of the following:
- Enter setup at the CLI Manager level prompt. HP Switch# setup.
- Select Run Setup in the Main Menu of the menu interface.
How do I clear the configuration on my Brocade switch?
Tap the “Enter” key a few times and the Brocade command prompt will display. Type the console password if requested and press the “Enter” key. Type “configDefault” and press the “Enter” key. The switch configuration is now reset to factory default settings.
How do I restore my hp to factory settings?
To execute the factory default reset on the switch, perform these steps:
- Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch.
- Continue to press the Clear button while releasing the Reset button.
- When the Self Test LED begins to blink, release the Clear button.
How do I restore my HP 1920 to factory settings?
Restoring to factory defaults
- Using a small, thin tool with blunt ends (such as a paper clip), press the Reset button on the front of the switch.
- Continue to press the Reset button until the Fault LED light begins to flash.
- Release the Reset button.
How do I reset my HP Deskjet 2510?
How to reset a ProCurve 2510-24g to default settings
- Press in both the Clear and Reset buttons (tiny buttons on the left edge)
- Release the Reset button after the port lights come on (~2 seconds)
- When the Self-Test LED starts flashing (to the left of the Clear and Reset buttons), release the Clear button.
How do I Reset my HP computer to factory settings Windows 10?
How do you factory reset an HP laptop with Windows 10?
- Click on the Start menu and choose the “Settings” option. …
- In the search bar, type “reset.”
- From there, choose the “Reset this PC” option once the results have popped up.
Does a hard Reset erase everything on HP laptop?
No it will not…. hard reset is simply hold down power button 30 seconds with no power supply attached. It is not the same as a cell phone reset.
How do I force start my HP laptop?
Turn off the computer, and then unplug the power cord. Disconnect any peripheral devices, and then remove the computer from any port replicator or docking station. Remove the battery from the computer. With the battery and power cord unplugged, press and hold the Power button for approximately 15 seconds.