Can you use power antenna wire for remote?
Some of the more common options for connecting the remote turn on wire when using a factory head unit are to the wire connected to a power antenna (older vehicles which do not turn off the antenna when not using the radio) or to the vehicle’s fuse box.
Does power antenna need connected?
Yes, these two wires should be connected together. This is what allows the radio to retract the antenna when it isn’t being used. Just because your wiring harness has a connection for this wire, it doesn’t necessarily mean that your car has this kind of motorized antenna.
Where does the remote wire go?
The turn-on wire (also called the remote wire) is located behind the stereo. On aftermarket stereos, it’s usually a blue and white wire. The remote wire will “tell” your amplifier to turn on whenever the stereo is powered up (usually, whenever the vehicle is turned on).
Where is the remote wire on a car stereo?
What is power antenna wire for?
It is how the radio tells the amps to turn on/off when you turn the radio on/off. Since it is a Pioneer radio and they use the standard colors, it should have a blue (or blue/white) wire for the remote.
What does power antenna do?
A power antenna is an electrically motorized automotive radio antenna that raises and lowers either manually with a dash-mounted switch or automatically by turning the radio on or off. … Unlike most car antennas adjusted directly by hand, power antennas retract completely beneath the surface that they are mounted on.
Can you use any wire for remote wire?
It doesn’t matter what kind of wire you use for a remote wire. Any copper wire will work when used as a remote wire. Since most speaker wires are made of copper metal, they can be used for remote wiring.
What color is the remote wire?
Wiring Harness Color Standards
| Wire Color | Wire Function |
|---|---|
| Red | Switch / Accessory |
| Black | Ground |
| Blue | Antenna Remote |
| Blue with White Stripe | Amplifier Remote Turn-on |
How do you turn on an amp without remote wire?
If the amp doesn’t have a remote, then simply use the contact of the reed relay to switch a power control relay for the amp.
What size should remote wire be?
18 gauge wire
AudioControl recommends 18 gauge wire for our car audio products, such as our line converters, EQs, crossovers and DSP processors.
What gauge is remote wire for AMP?
18 Gauge
18 Gauge 6 Color Combo 100 Feet per Roll (600 ft Total) Low Voltage Automotive Primary Wire for Car Stereo Amplifier Remote 12 Volt Trailer Harness Hookup Wiring. Usually ships within 7 days.
What is remote output?
This unit has an audio-sense remote output. Meaning when the radio is turned on, it senses an audio signal and sends a 12 volt signal through the remote output wire from the line output converter. That remote output wire needs to go to your external amplifier (2-channel or mono sub-amp) to signal it to turn on.
Can I use speaker wire for epicenter?
If your factory installed audio system has an amplifier, then use the speaker wires after the factory amplifier to feed a signal into The Epicenter Plus. The Epicenter Plus also works the best when it receives a full range signal.
What is a 18 gauge wire?
AWG stands for American wire gauge. It relates to the diameter of the wire. The more current capacity it can carry, the lower the AWG. A thicker 16AWG can carry 13 Amps, but a thinner 18AWG can only carry 10 Amps.
How many volts does a car stereo need?
Car radios use direct current (DC) voltage to power their electronics while home electronics use alternating current (AC) with a much higher voltage. In fact, car radios can work down to somewhere around 11 volts DC, with 12V to 14.4V being typical when a vehicle’s engine is running.
What should the sweep be set at on a epicenter?
The “Sweep” knob allows you to pick the center frequency that you want The Epicenter bass restoration circuit to “maximize”. The “Wide” knob adjusts how wide a frequency range The Epicenter will effect. The effective range of the sweep control is 27Hz – 63Hz.
How do you tune an epicenter?
What does an audio control epicenter do?
THE EPICENTER® PROCESSORS
The centerpiece of many champion sound installation systems. A patented process digitally maximizes the ultra-low bass on all types of source material. The Epicenter detects bass harmonics, then digitally recreates the underlying fundamental for the incredible punch and impact of live music.
What does wide and sweep on epicenter?
The “Sweep” knob allows you to pick the center frequency that. you want The Epicenter bass restoration circuit to maximize. The “Wide” knob. adjusts how wide of a frequency range The Epicenter will effect.
What is soundstream BX 108Z?
The BX-108Z has a unique equalization circuit that contours the restored bass to your speaker systems. Dash Mount Remote Control: The BX-108Z comes with Dash Mountable Remote Control allow you to enjoy the effects of the BX-108Z without leaving the driver’s seat.
How do I adjust my bass restoration processor?
Should I use an epicenter?
We always recommend you put the Epicenter® BEFORE an EQ or crossover. Since the Epicenter is adding frequencies to your signal, you would want to put it before any EQ or crossover in order to be able to adjust those frequencies.