How do I change the code on my Kwikset lock?
How do I reset my Kwikset digital lock?
1 Factory Reset
- Open your door.
- Extend the latch bolt.
- Slide up the cover to open the back of your lock, exposing the buttons beneath.
- Push and hold the reset button for 10 seconds, until the lock beeps.
- The light ring will flash red, then spin amber.
- The lock has now been restored and is ready to be set up again.
How do I reset my Kwikset SmartCode master code?
How do I enable/delete the mastercode on my Smartcode?
- Keep door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds).
- Enter new Mastercode.
- Press Lock button once.
- Re-enter Mastercode.
- Press Lock button once.
- Make sure switch #3 is on, and press the Program button once.
How do I program my Kwikset SmartCode?
How do I program my SmartCode 913 lock?
- Open the door.
- Remove battery cover.
- Press the program button once.
- Enter new user code.
- Press lock button.
- If programming is successful the keypad will flash green once, and you will hear one beep.
How do I reset my Kwikset SmartCode 913?
How do you reset a Kwikset 913 Deadbolt?
A factory reset will delete all codes associated with the lock. 3 Press the Program button once more. In 20 seconds, when the LED flashes green and you hear one beep, the lock has been reset.
Why is my Kwikset lock not working?
Take the battery pack out of the unit and depress the button labeled “Program” three times if the unit doesn’t operate properly after installation or fails to open with a key. Allow ten seconds to elapse, then hold down the “Lock” button while reinstalling the battery pack.
What is the master code for Kwikset lock?
The default Mastercode is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Make sure the lock is unlocked and the door is open.
How do you clear the code on a Kwikset lock 910?
Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red. Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
How do I remove a code from Kwikset SmartCode 909?
Deleting a user code In order to delete a user code, you must override the code by adding a different user code in the same position. For example, if you want to delete the third code, add a different user code in position three. NOTE: Test the old user code to make sure it can no longer unlock the door.
How do you unlock a Kwikset lock code?
To program the first user code:
- Press the button marked “program button” once.
- Using the keypad, enter a 4- to 8-digit code.
- Press the ‘LOCK” button to save the code.
- Extend the bolt by pressing- the “LOCK” button.
- Enter the new code number. The bolt should retract.
How do I turn off auto lock on Kwikset?
How do I turn off auto lock on Kwikset 888?
How do I turn off auto lock on Kwikset 913?
Make sure switch #3 is on, and press the Program button once. If you don’t immediately hear three beeps and see the keypad fl ash green three times, the Mastercode is disabled. Note: The lock will time out after five seconds.
How do I turn off auto-lock on door lock?
Press “Unlock” on the power door button one time to toggle the autolock/relock feature to “On” or “Off.”
Does the Kwikset aura lock automatically?
Yes, the auto–lock time delay can be customized using the Kwikset App within Bluetooth range Aura. The selectable time intervals are: 30 seconds, 1 minute, 3 minutes, 5 minutes, 10 minutes. Click here to view instructions.
How do you set auto-lock on Kwikset Powerbolt 2?
How to enable/disable Auto–Lock on my Powerbolt 2?
- Make sure the lock is unlocked and the door is open.
- Enter your existing Mastercode.
- Press the lock button. You will hear one beep.
- Press 1 – 1.
- Press the lock button. You will hear two beeps if successful. If you hear three beeps, it was unsuccessful. Repeat from step 1 slowly.