What do I put under cedar shingles?
The Cedar Shake and Shingle Bureau recommends installation over Type 30 asphalt felt underlayment for red cedar shingles and shakes. Install the felt paper with minimum 6-inch overlaps on vertical joints, 2 inches on horizontal laps, and 4 inches wrapped each way at inside and outside corners.
How much do you overlap cedar shingles?
Leave a gap of approximately 1/8” to 1/4” (0.3 to 0.6 cm) between neighboring shingles to allow for expansion due to moisture. Joints of successive courses must always be offset by at least 1 1/2” (3.8 cm) to prevent water build-up. Treat shingle imperfections the same way.
How do you start the first row of cedar shingles?
Can you use a nail gun on cedar shingles?
“Use either rust-resistant staples or shingle nails (1-1/4” to 1-1/2” long), galvanized, in stainless steel or aluminum”. It simply means that the best nail gun for cedar shingles will either be a stapler nail gun or any nailer that can shoots the recommended nails or staples!
Can you use a brad nailer for shingles?
Large-body nailers typically include framing nailers and roofing nailers. These nailers are used for more technical projects such as framing out a basement or installing roofing shingles. For woodworking projects, a brad nailer is a good choice. If you‘re constructing a fence, a framing nailer is a good option.
Can you staple cedar shingles?
The Cedar Shake & Shingle Bureau prefers the use of nails, however if you choose to use staples they must be stainless steel Type 316 in locations within fifteen (15) miles of salt water. For locations outside of the salt water zone – stainless steel staples Type 304 or Type 316 must be used.
Is it better to nail or staple shingles?
Fasteners for asphalt shingles should be roofing nails or staples. The head of a roofing nail or the crown of a staple is what actually holds a shingle in place. If staples are properly installed, they offer nearly the same wind resistance as nails. The problem with staples is the orientation of the staple crown.
Can you use crown staples for cedar shingles?
The way the grain is most shingles I think nails would make them prone to split. On all the cedar shake gazebo roofs that I do they are stapled. Use a narrow crown stapler not a wide crown stapler & turn the pressure down some.
What nails do you use for cedar siding?
Hot-Dipped galvanized, aluminum and stainless steel nails are all corrosion-resistant and all can be used to nail Western Red Cedar. Other types of nails are not recommended. They can rust and disintegrate and react adversely with the natural preservative oils present in cedar resulting in stains and streaks.
Do you need furring strips for cedar siding?
Cedar is a material that needs to be allowed to flex once installed. It is highly recommended that the product be installed over furring stripes that are attached to the studs of a wall. For siding that is being installed in a horizontal pattern, the furring strips should be attached vertically.
Should you caulk cedar siding?
Generally, you don’t need to caulk cedar siding that has been installed within the last 10-15 years. However, sometimes poor workmanship on a building could result in you having to caulk siding and joints. And other times, old cedar siding will simply need a bit of upkeep.
Can I use galvanized nails in Cedar?
Nails. Hot-dipped galvanized, aluminum and stainless steel nails are all corrosion-resistant and all can be used to nail Western Red Cedar. Other types of nails, such as electroplated, are not recommended.
What kind of screws do you use with cedar?
Stainless steel is the best choice when using western red cedar. Hot dipped galvanized is the most widely used (and one of the most economical fasteners), and aluminum is an option, too. These fasteners are all corrosion-resistant.